-
I bought the cheapest power supply I could find. It cost me 3x the quote.
-
Argument 1: The spec sheet says 350W, but nobody reads the derating curve
-
Argument 2: Fluorescent-era thinking still drives driver selection
-
Argument 3: Time pressure is where cheap decisions get locked in
-
"But the client just wants the cheapest option"
-
The cheapest power supply is the one you only buy once
-
Argument 1: The spec sheet says 350W, but nobody reads the derating curve
I bought the cheapest power supply I could find. It cost me 3x the quote.
I've spent nine years handling commercial lighting and power supply orders for integrators and electrical contractors. In that time, I've personally made (and documented) three significant mistakes totaling roughly $6,400 in wasted budget. One of those mistakes was buying a knock-off LRS-350-12 to save $22 over the Mean Well unit. That "savings" turned into a $2,300 problem across one order of 18 fixtures.
So here's my blunt take: if your power supply spec comes down to whoever quotes the lowest unit price, you're already losing. The lowest quote isn't the lowest cost—not even close.
This isn't about brand loyalty. I don't work for Mean Well. I work for a team that moves lighting projects out the door, and I've watched too many cheap-driver decisions come back around to the same handful of failure modes.
Argument 1: The spec sheet says 350W, but nobody reads the derating curve
Most buyers focus on the wattage number in the headline and completely miss the derating curve buried on page 3 of the datasheet. That's the outsider blindspot. A power supply rated at 350W doesn't run at 350W in a sealed enclosure at 60°C ambient. It derates—often down to 60-70% of rated output.
For a mean well lrs-350-12 power supply, the spec sheet is actually pretty clear about ambient temperature vs. load. When I bought the cheap clone, the datasheet had the same headline spec but a much steeper derating curve. On a retail ceiling install where the drivers lived in a tight soffit, the clones were running near 80% load at elevated temps. Two failed within eight weeks. The Mean Well units in the adjacent zone kept chugging.
The question everyone asks is "who's cheapest?" The question they should ask is "what does the derating curve look like at the actual ambient temperature in this project?" That one question has saved me more grief than any supplier relationship.
Argument 2: Fluorescent-era thinking still drives driver selection
This was true fifteen years ago when the ballast was treated as a dumb, disposable part of the fixture. Today, with LED retrofits—especially when you're stripping fluorescent fixtures out of a drop ceiling and figuring out how to remove a fluorescent light cover from a drop ceiling to access the wiring—the driver is doing far more work than a ballast ever did.
The "driver is just an accessory" thinking comes from an era when a magnetic ballast cost $12 and lasted forever. LED drivers now handle 3-in-1 dimming (resistor, PWM, or 0-10V), constant-current regulation, thermal protection, and sometimes DALI or 0-10V control signalling. When you're specifying a remote spotlight setup running off a dimmed circuit, the driver isn't a footnote—it's the whole reason the remote spotlight image you promised the client will actually render the way they expect.
I've seen a spec where the buyer matched the driver wattage to the total LED load, then wired the dimming circuit wrong because the datasheet used a resistor-based dimming scheme instead of 0-10V. The fixture worked. It just wouldn't dim below 30%. The client asked why the spotlight image in the visualisation showed a 5% dim state and the reality was full-blast. That's a credibility problem, not a parts problem.
Argument 3: Time pressure is where cheap decisions get locked in
In September 2022 I had a Friday deadline for a showroom retrofit. Normally I'd get three quotes, check the datasheets, verify the dimming topology against the lighting plan. But the client moved the opening date and I had about two hours before the purchase order had to go in. Went with the lowest quote from a distributor I'd used once. No time to check the thermal derating on the datasheet. No time to confirm whether the "3-in-1 dimming" actually covered the resistor range the lighting designer had specified.
It looked fine on paper. The result came back as a callback three weeks later: two drivers dead, three more flickering on the dimming circuit. The redo cost $2,300 across replacement parts, labour, and a credit I had to give the client for the delay. In hindsight, I should have pushed back on the timeline and asked for 24 hours to spec it properly. But with the client's GM waiting on the opening date, I made the call with incomplete information.
That September is why our team now has a pre-approval checklist with one hard rule: no POs on power supplies without a datasheet review, even if it's after hours. We've caught 47 potential errors using this checklist in the past 18 months, and most of them were derating or dimming-topology mismatches that would have surfaced six months into the installation.
"But the client just wants the cheapest option"
Yeah, I've heard that one. Here's the thing: when a client says "cheapest," they're usually saying "lowest total cost," not "lowest invoice line." Those are different sentences with different answers.
Run the total-cost math on a power supply and it looks like this:
- Unit price
- Setup or programming fee (some drivers need resistor or PWM configuration)
- Shipping and lead time certainty
- Warranty replacement turnaround (if the unit fails, how many days of downtime?)
- Labour to re-open the ceiling or soffit if a driver has to be replaced
- Client-relationship cost if the lighting doesn't perform as specified
The lowest quoted unit price often isn't the lowest total cost. I've made that math go wrong on my own POs enough times that I don't need to lecture anyone about it—I just ask them to fill in all six lines before they send the order.
And on the "mean well led lights" question that shows up in my inbox a lot: no, Mean Well doesn't make LED fixtures themselves. They make the drivers and power supplies that keep fixtures running. That distinction matters because you can buy a well-built fixture and strangle it with a badly selected driver. The power supply is the part of the system most likely to be spec'd by whoever is cheapest that week, and that's exactly backwards.
The cheapest power supply is the one you only buy once
My position hasn't changed since that September: buy the driver and power supply solution that's right for the installation, not the one that's cheapest on the quote sheet. If you're installing LRS-350-12 replacements, read the derating curve. If you're wiring remote spotlights into a dimmed circuit, verify the dimming topology before the PO goes in. If you're pulling fluorescent covers off a drop ceiling in a retrofit, take the extra ten minutes to spec the driver properly—because the labour to get back up there is the part nobody budgets for.
The $22 I saved on the cheap unit cost me $2,300 in rework. I don't need to make that mistake a fourth time to know which side of the ledger I want to be on.
