There's No Universal “Good” Lighting Spec
Every week, a spec sheet lands in my inbox with the same question attached: “Will this pass?” And every week, the honest answer is: it depends on what the fixture is doing. I've been signing off on lighting deliveries for about six years now—roughly 200 SKUs a month before they ever reach an installer—and I've stopped pretending there's one checklist. A venetian chandelier and a feit electric class 2 power supply model fedc5v3a fail for completely different reasons.
So here's how I actually break it down. Three scenarios cover most of what I see: statement fixtures, dimmable loads on a Class 2 supply, and LED strip runs. Find the one that sounds like your project, then read the section that applies.
Scenario A: Statement Fixtures
This is the chandelier category—jacqueline chandelier, venetian chandelier, anything hanging in a lobby or over a dining table where people will look at it before they look at anything else. My job here isn't electrical. It's perceptual.
What I check first is finish consistency across the fixture, not the spec sheet. A chandelier can hit every number on paper and still look wrong if two arms are a half-shade apart in finish. In our Q1 2024 audit, we rejected a 40-piece crystal fixture order because the plating on the arms ranged from warm brass to almost olive under the same light—normal tolerance didn't cover it, and the vendor called it “within industry standard.” We sent it back. Now every contract for decorative fixtures includes a finish-match requirement.
Second thing: CRI at the operating dim level, not at full output. This is the reverse-intuitive one. Most buyers spec CRI 90+ and feel good about it. But CRI is measured at full power on a lot of datasheets, and a fixture that reads 92 at 100% can drop noticeably at 20% when the driver shifts. If the space will run dimmed most of the evening—and most lobbies and restaurants do—test it dimmed. ANSI C78.377 gives you a defensible way to talk about color temperature consistency across a batch; use it as your baseline, then verify at the level the customer will actually see.
Bottom line: for statement fixtures, the customer's first impression of your company is that fixture. If it's uneven, they don't blame the factory. They blame you.
Scenario B: Dimmable Loads and Class 2 Power Supplies
Now we're in the range where things flicker and people call me angry.
feit electric dimmable bulbs are a good example of why “dimmable” on a box is only half the answer. Dimmable means it's designed to dim with a compatible control—it doesn't mean it'll dim well on every dimmer in the building. Leading-edge and trailing-edge dimmers behave differently, minimum loads matter, and a bulb that's smooth on one circuit can buzz on another. When we spec feit electric dimmable bulbs for a project, we don't sign off until we've tested them on the actual dimmer model going into the building. I've been burned by this. In 2023, I assumed “dimmable” meant universal compatibility and approved a substitution without testing. Turned out “compatible” meant with a specific dimmer family. We ate a rework and a very uncomfortable client call.
Then there's the supply side. The feit electric class 2 power supply model fedc5v3a shows up in more conversations than you'd expect, usually because someone wants to swap it for whatever's on the shelf. Don't. Under UL 1310, Class 2 power units are output-limited by design—the classification caps voltage and power so a fault can't turn into a fire. The model number usually encodes the voltage and current envelope (check the label, don't assume from the string), and your load has to fit inside both. A 5 V / 3 A supply is not interchangeable with a 12 V unit just because the connector matches. And when we quote feit-electric products for a project, the testing on our end doesn't change.
Here's the penny-wise trap. On one run, we saved roughly $400 by substituting a generic supply that “met the same specs.” Three weeks later, installers were reporting flicker at the end of long runs. The fix was new supplies plus labor—about $2,800, and a delay that pushed a client's opening. The cheap supply wasn't cheaper. It just moved the cost to a place I couldn't see it yet.
The brand-image angle: flicker reads as “cheap” to anyone standing in the room, even if they can't explain why. Your client won't say “the driver's minimum load is mismatched.” They'll say the lighting feels off, and that's the impression they carry. That's a red flag on the whole install, not a minor defect.
Scenario C: LED Strip Runs
This is the DIY and integrator crowd—where to cut led strip daybetter, or any other brand, is one of the most common searches I see from installers. The answer is more consistent than people expect: most 12 V strips are cuttable every 3 LEDs (about 50 mm), and most 24 V strips every 6 LEDs. But the actual cut marks are printed on the strip, usually as a line through copper pads. If you can't find a mark, don't guess—measure to the nearest marked pad or you'll kill that section.
Two things I check on strip runs that installers often skip:
- Voltage drop. Long runs dim at the far end. If a run pushes past roughly 5 meters on a single feed, plan a second feed rather than trusting the strip to carry it evenly.
- Supply headroom. Size the supply above the load—around 20% headroom is the working rule—but don't overdo it. A wildly oversized supply can sit below its efficient range and run oddly. Match, don't max out.
And a boundary I'll state plainly: I'm not a licensed electrician. If your question is about local code, circuit sizing, or whether a Class 2 circuit can share a raceway with line voltage, consult your electrician. What I can tell you is how to catch the failures that happen before the inspector ever shows up.
How to Tell Which Scenario You're In
If you're still not sure which section applies, answer three questions:
- Will anyone look at the fixture itself first? If yes, you're in Scenario A. Prioritize finish and dimmed CRI over raw output.
- Does it dim, or does it run off a separate supply? If yes, you're in Scenario B. Test the exact dimmer and match the supply envelope to the load—no substitutions without a bench test.
- Is it a cuttable linear run? If yes, you're in Scenario C. Find the printed cut marks and size feeds for voltage drop, not just for the strip's rated wattage.
Most projects actually touch two of the three, and that's where people get into trouble—a chandelier with integral dimmable bulbs is Scenario A and B wearing the same box. In that case, run the stricter check from each.
And if you only remember one thing: the spec that passes inspection and the spec that keeps your client happy aren't always the same number. I've watched a batch clear every tolerance and still lose a customer on first sight. That's the cost nobody puts on the quote.
